Before using a brake pad repair kit for your car, it's crucial to check the brake pad thickness. As a supplier of brake pad repair kits for cars, I understand the importance of this step in ensuring the safety and performance of your vehicle. In this blog post, I'll guide you through the process of checking brake pad thickness and provide some tips to keep in mind.
Why Check Brake Pad Thickness?
Brake pads are a critical component of your car's braking system. They create friction against the brake rotors to slow down and stop your vehicle. Over time, brake pads wear down due to the constant friction. If the brake pads become too thin, they won't be able to provide sufficient stopping power, which can lead to longer stopping distances and potentially dangerous situations.


By regularly checking the brake pad thickness, you can catch wear issues early and replace the brake pads before they cause problems. This not only helps keep you and your passengers safe but also extends the lifespan of your brake rotors and other braking components.
Tools You'll Need
To check the brake pad thickness, you'll need the following tools:
- A jack and jack stands: These are used to lift the car safely off the ground.
- A lug wrench: To remove the wheels.
- A flashlight: To help you see inside the wheel well.
- A brake pad thickness gauge: This tool is specifically designed to measure the thickness of brake pads. If you don't have a gauge, you can also use a ruler or caliper.
Step-by-Step Guide to Checking Brake Pad Thickness
-
Park Your Car on a Level Surface and Engage the Parking Brake
Make sure your car is in park (for automatic transmissions) or in gear (for manual transmissions). This will prevent the car from rolling while you're working on it. -
Loosen the Lug Nuts
Use the lug wrench to loosen the lug nuts on the wheel you want to check. Don't remove them completely at this point. -
Lift the Car
Use the jack to lift the car until the wheel is about 6 - 8 inches off the ground. Then, place the jack stands under the car's designated lifting points and lower the car onto the stands. This provides a stable and safe working platform. -
Remove the Wheel
Once the car is safely supported on the jack stands, remove the lug nuts completely and take off the wheel. Place the wheel flat on the ground next to the car. -
Locate the Brake Pads
Shine the flashlight into the wheel well to locate the brake pads. They are usually located on either side of the brake rotor. The brake pads are held in place by Brake Pad Clips for CHEVROLET (for Chevrolet models), D1589 Brake Pad Clips For Vw (for VW models), or Brake Pads Springs Clips for JEEP (for Jeep models), depending on your vehicle make and model. -
Measure the Brake Pad Thickness
Use the brake pad thickness gauge, ruler, or caliper to measure the thickness of the brake pads. Place the measuring tool against the friction material of the brake pad (the part that makes contact with the rotor). Measure the thickness at several points around the pad to get an accurate reading. -
Compare the Measurements to the Manufacturer's Specifications
Check your car's owner's manual or the manufacturer's website for the recommended brake pad thickness. Most brake pads should be replaced when they reach a thickness of about 3 - 4 millimeters. If the thickness of your brake pads is close to or below this limit, it's time to replace them. -
Repeat the Process for the Other Wheels
Brake pads can wear unevenly, so it's important to check all four wheels. Repeat steps 2 - 7 for each wheel on your car. -
Put the Wheel Back On
Once you've finished checking the brake pads, put the wheel back on the car. Hand-tighten the lug nuts as much as possible, then use the lug wrench to tighten them further. Make sure the lug nuts are tightened in a star pattern to ensure even tightening. -
Lower the Car
Use the jack to lift the car slightly off the jack stands, remove the stands, and then lower the car back to the ground. Finally, use the lug wrench to give the lug nuts one last tightening.
Tips for Checking Brake Pad Thickness
- Check the Brake Pads Regularly: It's a good idea to check your brake pad thickness every 10,000 - 15,000 miles or at least once a year. This helps you catch wear issues early and avoid costly repairs.
- Look for Other Signs of Brake Wear: In addition to measuring the brake pad thickness, look for other signs of brake wear, such as squeaking or grinding noises when you apply the brakes, a pulsating brake pedal, or a longer stopping distance. These could indicate that your brake pads are worn out or that there are other problems with your braking system.
- Replace Brake Pads in Pairs: To ensure even braking performance, it's recommended to replace the brake pads on both wheels of the same axle at the same time. This helps prevent uneven wear and ensures that your car stops safely and smoothly.
Conclusion
Checking the brake pad thickness before using a brake pad repair kit is an important step in maintaining the safety and performance of your car. By following the steps outlined in this blog post and using the right tools, you can easily check the brake pad thickness and determine if it's time to replace them.
As a supplier of brake pad repair kits for cars, we offer a wide range of high-quality brake pad repair kits that are designed to fit various makes and models of vehicles. Our kits include everything you need to replace your brake pads, including the brake pads themselves, Brake Pad Clips for CHEVROLET, D1589 Brake Pad Clips For Vw, and other necessary components.
If you're interested in purchasing a brake pad repair kit or have any questions about brake pad maintenance, please feel free to contact us for more information and to discuss your specific needs. We're here to help you keep your car's braking system in top condition.
References
- Your Car's Owner's Manual
- Automotive Repair Manuals
- Online Resources from Brake Pad Manufacturers


